Thank you very much @Timwis, and I apologize, I didn’t mean to drop the review exactly the same day you did.
3 Likes
lol, you could of made your photos a bit crapier (is that even a word)! All good you were not to know mate! 
3 Likes
Believe me the quality of my photos has nothing to do with being lazy, I only have an old iPod, lol! They are the best photos possible for me to do with what I have! 
3 Likes
Your photos are fine mate. I just use my S21 Ultra, but if you’re like me, I’ll take 200, and use 20.
3 Likes
At least 200 yeah, it’s the clear magnification I can’t get, if i blew them up so you could read the writing on the airflow pins for example the photo would be very blurred!
3 Likes
Put the word out, in the network of company’s you do review’s for…that you’d like to review a camera…Hehe, problem solved?! 
3 Likes
Go fund me, lol!
3 Likes
I can’t afford a quality digital camera so I expect others to buy me one, lol! 
3 Likes
2 winners SD, great review as usual Are you typically an MTL vaper?
5 Likes
I have put this on my thread but will put it here for those that only read this review as my views on this forum are well down compared to the other places I post (only 61 views for my last review over a fortnight ago, seriously must change my deodorant, lol)!
Just a word of note, the single round wire coil that I didn’t use which is labelled as 0.4ohm is clearly labelled wrong as it should be even higher ohms than the clapton so my guess would be 1.4ohm! Because it’s labelled wrong might not even be Kanthal!
5 Likes
LOL, I don’t think I even checked the ohmage on that one Tim. I’ll have to see if it’s still floating around.I checked the Ni80 (first coil on deck), and after I pulsed and stroked it, it came out very close.
3 Likes
Yeah I used the Clapton and then one of my favourite MTL hybrid Aliens, I might be wrong but 7 wraps KA 2.5ID, 28ga just doesn’t even sound close to 0.4ohm, has to be a mistake!
4 Likes
Just a courtesy post to get both Aromamizer Classic reviews back together so peeps will hopefully read both!
4 Likes
Cheers Tim !!!
4 Likes
Regarding this minor issue. Expanding on this, I was talking to another reviewer, who had not really flooding, but some over-juicing/gurgling, after re-filling the tank. During the FIRST part of my test(s) I did not use enough cotton, and had some minor weeping from the air flow pins. I contacted Maggie from SteamCrave, and she agreed, that more cotton would resolve this, and it did. I think because I had early on, went heavier with the cotton, I didn’t really have an issue re-filling. After numerous re-fills, and wick changes, I did notice that with a LIGHTER cotton load, after re-filling, I did get some “wet” hits, but only for about 3 or 4 hit, then smooth sailing throughout the entire rest of the tank.
I experimented, with again, heavier cotton loads, and it ceased. Not sure if it’s a con or not, but an issue to be aware of, if you do not use enough cotton. In my experience, if you go with a heavier cotton load, it is a non-issue.
3 Likes
I also no longer have issues since now using more cotton as long as I fill quickly but yep more cotton and not leaving the tank unscrewed long during the re-fill process eliminates it! This is one very good MTL RTA!!! 
2 Likes
I can’t keep track of who all has this Hadron Mini mod, but you should all update the firmware from the latest INTERNATIONAL Escribe suite. It can be found here, and will have SP45.1 INT for the mod.
4 Likes